Hay and forage equipment - Square baler M236-3503
John Deere | L634 DEMO
Hay and forage equipment | M236-3503
134 900 EUR excl. VAT
Machine description:Bale dimensions: 120 × 90 (width × height) Bale length: Adjustable 0.6 – 3.0 m Pickup width: 2.30 m, stainless steel pickup bands Pickup: 5 tine bars, hydraulic pickup lift/lower, 34 cm diameter, slip clutch Windrow press roller Reinforced Hardox feed rotor, bolt-on tines, 59 cm diameter Adjustable feeder fork (fixed cycle or crop-flow dependent) Openable pre-compression chamber floor for blockage removal Reinforced main drive with large flywheel Reinforced plunger bearings, 125 mm High-capacity plunger, 46 strokes per minute High-capacity Heavy Duty MaxiCut 23 rotor, made of Hardox steel, with 23 double-hardened cutting knives Rotor diameter: 590 mm Theoretical chop length: 45 mm depending on number of engaged knives (0 / 11 / 12 / 23) Spring-loaded stone protection for cutting knives Drive: 1000 rpm PTO, 21 spline, wide-angle PTO shaft with slip clutch ISOBUS control system Bale length adjustable from terminal: 60–300 cm Required tractor hydraulics: 1× SCV, Power Beyond, Load Sensing (LS) 6 double-knot knotters, with turbines for cleaning the tying system Cleaning system: Two turbines with independent hydraulic drive Storage for 30 twine rolls Automatic central lubrication system Bale chamber with four hydraulic density cylinders Towing hitch: K80 ball hitch (80 mm coupling) Caster-type swiveling pickup wheels Hydraulically folding bale discharge ramp, with partial bale ejection capability Steerable tandem axle with 620/55R22.5 tires, hydraulic brakes 40 km/h marking, wide-load marking, beacon light Low-friction wear plates in bale chamber Moisture sensor, range 9% – 40% Filler plates for rotor knife slots LED work lights Grease gun with quick-fill system and adapter for automatic lubrication pumpDisclaimer text area.
machine main image
❮❯
machine-0
machine-1
machine-2
machine-3
machine-4
machine-5
machine-6
machine-7
machine-8
machine-9
View all (18)
John Deere | L634 DEMO
Hay and forage equipment | M236-3503
134 900 EUR excl. VAT
Disclaimer text area.

Machine description

Bale dimensions: 120 × 90 (width × height) Bale length: Adjustable 0.6 – 3.0 m Pickup width: 2.30 m, stainless steel pickup bands Pickup: 5 tine bars, hydraulic pickup lift/lower, 34 cm diameter, slip clutch Windrow press roller Reinforced Hardox feed rotor, bolt-on tines, 59 cm diameter Adjustable feeder fork (fixed cycle or crop-flow dependent) Openable pre-compression chamber floor for blockage removal Reinforced main drive with large flywheel Reinforced plunger bearings, 125 mm High-capacity plunger, 46 strokes per minute High-capacity Heavy Duty MaxiCut 23 rotor, made of Hardox steel, with 23 double-hardened cutting knives Rotor diameter: 590 mm Theoretical chop length: 45 mm depending on number of engaged knives (0 / 11 / 12 / 23) Spring-loaded stone protection for cutting knives Drive: 1000 rpm PTO, 21 spline, wide-angle PTO shaft with slip clutch ISOBUS control system Bale length adjustable from terminal: 60–300 cm Required tractor hydraulics: 1× SCV, Power Beyond, Load Sensing (LS) 6 double-knot knotters, with turbines for cleaning the tying system Cleaning system: Two turbines with independent hydraulic drive Storage for 30 twine rolls Automatic central lubrication system Bale chamber with four hydraulic density cylinders Towing hitch: K80 ball hitch (80 mm coupling) Caster-type swiveling pickup wheels Hydraulically folding bale discharge ramp, with partial bale ejection capability Steerable tandem axle with 620/55R22.5 tires, hydraulic brakes 40 km/h marking, wide-load marking, beacon light Low-friction wear plates in bale chamber Moisture sensor, range 9% – 40% Filler plates for rotor knife slots LED work lights Grease gun with quick-fill system and adapter for automatic lubrication pump

General information

General

BrandJohn Deere
ModelL634
Extra titleDEMO

Machine data

Serial number1KUL634HEPC002230
Year of manuf.2023

Condition

StateUsed
General conditionReally good

Technical data

Technical data

Working width2.3 m

Make an offer!

Make an offer and we will come back to you shortly.
300/300

Sales information

Wihuri OÜ
Tambet EslasTambet EslasUsed equipment line manager
+37254420278tambet.eslas@wihuriagri.com
Location
Tehnika 5, 50104, Tartu
Tehnika 5, 50104, Tartu
John Deere L634
John Deere L634
134 900 EUR excl. VAT
John Deere L634Machineric IDM236-3503Year of manuf.2023
Contact
Tambet Eslas
Location
134 900 EUR
Tehnika 5, 50104, Tartu

Make an offer!

Make an offer and we will come back to you shortly.
Disclaimer text area.